Rock particles machine _ universal grinder is commonly used in the pharmaceutical machinery equipment, smash - Mixed - drying - pelleting whole production process, they are in different stages of production, the structural principle of the rock particles are described below and universal grinder the safe use of points.
The principle of the structure of the rock particles,
Rock particles machine as if its name as a wet powder mixture of positive and negative rotation of the rotating drum, mandatory equipment made of particles through the sieve, sieve using wire mesh, installed demolition of a simple, adjustable elastic. Mechanical main components enclosed in the body, together with the lubrication system, the production process running smoothly. The whole appearance of stainless steel. Meet the GMP standard, quality and economic efficiency of the particles significantly improved.
The structure of the rock particles
Body: body is an independent rectangular cylinder on the device closed bearing and powder bucket connection, pink bucket toward the body.
, Particle manufacturing equipment: rotating drum lying set the bucket in the powder below, front and rear bearing supports for the inverted rotary rack drive, the end of the bearing cap is movable assembly and disassembly, as long as the spin under a wing nut, the bearing cap and rotating drum to be pulled out, place the roller at both ends of the system has a convex side ring.
Gearbox: worm gear drive, inside the reservoir oil, the endoscope can be observed on the box, to observe the functioning of the oil reserves, the worm outer end, equipped with the eccentric shaft, driven by the rack for reciprocating movement.
4, folder sieve tube: device on both sides of the rotary drum, steel pipe manufacturing, in the middle to open a long trough, both ends of the embedded slot of the screen, turn the flower-shaped hand wheel will screen wrapped in a cylindrical rotating drum hand wheel, gear shore, tightness can be adjusted.
5, the motor frame: a screw bolt firmly, the motor mounted on the iron, when the rotation of the screw bolt, the motor up and down movement for adjustment of belt.
Rock particles machine suitable humidity of the powder mixture into the hopper by the cutter wheel swing back and forth, swing role of the rotating drum, through a wire sieve, wet powder raw materials, research into particle extrusion material from the sieve granulated. Bulk material in the drum, impact crusher, and force through sieve made of particles. Material contact points are made of stainless steel, this is the case not only looks elegant and easy to clean, good standing of the user's point of view for users to consider only that rock particles machine also has a simple, low power consumption advantages.
Rock particles machine is mainly applied in the pharmaceutical, chemical, food industry, manufacturing a variety of particles to suppress the various molding products after drying for rock particles, the machine can also be used to crush dry material condenses into massive.
Universal grinder safety advice for users
Should be a universal grinder start idle 2-3 minutes, without exception after feeding.
Universal grinder after installation to check the various components of the fastening AMD universal grinder also want to check the belt tightness is appropriate, whether the motor shaft and universal grinder shaft parallel.
3, universal before the start of the grinder, first hand rotation of the rotor, check whether the operation of normal flexible chassis and whether the collision phenomenon, the correct direction of rotation of the rotor, good motor and universal grinder lubrication.
4, on closer inspection of material, to avoid metals, stones and other hard objects into the crushing chamber to cause the accident.
Feeding, the staff should stand universal grinder side, wounded face to prevent the rebound out of the debris. Crushed long stalk hand can not grasp too tight to prevent hands being brought into.
Do not replace the pulley to prevent the speed is too high or too low.
Feeding, stop stop, stand inside the material rule out clean, then cut off the power shutdown. After the shutdown for cleaning and maintenance.
8, 300 hours after the universal grinder job to be cleaning bearings, oil change; installed oil to full bearing gap of 1/3 as well, should not exceed a maximum of 1/2. Downtime, you should remove the belt.
Universal grinder should be fixed in the cement foundation. Such as frequent changes in the workplace, universal grinder and electric motors to be installed on the base made with angle.
10, the feed should be uniform, found noises, bearings, and the body temperature is too high or outward spray of material phenomena, should immediately stop inspection, troubleshooting. |
Rock particles machine _ universal grinder structural principle and safety of the use of points